 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| BTS 247 Z Speed TEMPFET N-Channel Enhancement mode Logic Level Input Analog driving possible Fast switching up to 1 MHz Potential-free temperature sensor with thyristor characteristics Overtemperature protection Avalanche rated 1 5 VPT05166 Type BTS 247 Z VDS 55 V RDS(on) 18 m Package P-TO220-5-3 P-TO220-5-62 TO-220-5-43 Ordering Code Q67060-S6001-A2 Q67060-S6002-A2 Q67060-S6006 D Pin 3 and TAB G Pin 1 A Pin 2 Temperature Sensor K Pin 4 S Pin 5 Pin 1 2 3 4 5 Symbol G A D K S Function Gate Anode Temperature Sensor Drain Cathode Temperature Sensor Source 1 2000-05-17 BTS 247 Z Maximum Ratings Parameter Drain source voltage Drain-gate voltage, RGS = 20 k Gate source voltage Nominal load current (ISO 10483) VGS = 10 V, VDS Symbol VDS V Value 55 55 20 A Unit V DGR ID(ISO) Continuous drain current 1) TC = 100 C, VGS = 4.5V Pulsed drain current Avalanche energy, single pulse Power dissipation TC = 25 C Operating temperature 2) Peak temperature ( single event ) Storage temperature DIN humidity category, DIN 40 040 IEC climatic category; DIN IEC 68-1 1current limited by bond wire 2Note: Thermal trip temperature of temperature sensor is below 175C 2 2000-05-17 ID = 12 A, RGS = 25 VGS = 4.5 V, VDS 0.5 V, TC = 85 C ID ID puls EAS Ptot Tj Tjpeak Tstg 0.5 V, TC = 85 C -40 ...+175 200 -55 ... +150 E 40/150/56 VGS 12 19 33 180 1.3 120 J W C BTS 247 Z Thermal Characteristics Parameter Characteristics junction - case: Thermal resistance @ min. footprint Thermal resistance @ 6 cm2 cooling area 1) Electrical Characteristics Parameter at Tj = 25C, unless otherwise specified Static Characteristics Drain-source breakdown voltage VGS = 0 V, ID = 0.25 mA Gate threshold voltage, VGS = VDS ID = 90 A ID = 250 A Zero gate voltage drain current VDS = 50 V, VGS = 0 V, Tj = -40 C VDS = 50 V, VGS = 0 V, Tj = 25 C VDS = 50 V, VGS = 0 V, Tj = 150 C Gate-source leakage current VGS = 20 V, VDS = 0 V, Tj = 25 C VGS = 20 V, VDS = 0 V, Tj = 150 C Drain-Source on-state resistance VGS = 4.5 V, ID = 12 A VGS = 10 V, ID = 12 A RDS(on) 22 15 28 18 IGSS 10 20 100 100 m IDSS 0.1 0.1 1 100 nA VGS(th) 1.2 1.6 1.65 2 A V(BR)DSS 55 V Symbol min. Values typ. max. Unit Symbol min. RthJC Rth(JA) Rth(JA) - Values typ. 33 max. 1.25 62 40 Unit K/W 1 Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70m thick) copper area for drain connection. PCB mounted vertical without blown air. 3 2000-05-17 BTS 247 Z Electrical Characteristics Parameter at Tj = 25C, unless otherwise specified Dynamic Characteristics Forward transconductance VDS>2*ID *RDS(on)max , ID = 33 A Input capacitance VGS = 0 V, VDS = 25 V, f = 1 MHz Output capacitance VGS = 0 V, VDS = 25 V, f = 1 MHz Reverse transfer capacitance VGS = 0 V, VDS = 25 V, f = 1 MHz Turn-on delay time VDD = 30 V, VGS = 4.5 V, ID = 45 A, Rise time RG = 3.6 td(on) 15 25 ns Crss 230 290 Coss 410 515 Ciss 1380 1730 pF gfs 10 S Symbol min. Values typ. max. Unit VDD = 30 V, VGS = 4.5 V, ID = 45 A, Turn-off delay time VDD = 30 V, VGS = 4.5 V, ID = 45 A, Fall time RG = 3.6 VDD = 30 V, VGS = 4.5 V, ID = 45 A, Gate Charge Characteristics Gate charge at threshold VDD = 40 V, ID = 0.1 A, VGS = 0 to 1 V Gate charge at 5.0 V VDD = 40 V, ID = 45 A, V GS = 0 to 5 V Gate charge total VDD = 40 V, ID = 45 A, V GS = 0 to 10 V Gate plateau voltage VDD = 40 V, ID = 45 A 4 2000-05-17 RG = 3.6 RG = 3.6 tr - 30 45 td(off) - 30 45 tf - 20 30 Qg(th) Qg(5) Qg(total) V(plateau) - 2 35 60 4.5 3 55 90 - nC V BTS 247 Z Electrical Characteristics Parameter at Tj = 25C, unless otherwise specified Reverse Diode Inverse diode continuous forward current TC = 25 C Inverse diode direct current,pulsed TC = 25 C Inverse diode forward voltage VGS = 0 V, IF = 90 A Reverse recovery time VR = 30 V, IF =IS, diF/dt = 100 A/s Reverse recovery charge VR = 30 V, IF =IS, diF/dt = 100 A/s Sensor Characteristics For temperature sensing, i.e. temperature protection, please consider application note "Temperature sense concept - Speed TEMPFET". For short circuit protection please consider application note "Short circuit behaviour of the Speed TEMPFET family". All application notes are available at http://www.infineon.com/tempfet/ Symbol min. IS IFM VSD trr Qrr 33 180 - Values typ. 1.1 75 0.15 max. 1.7 115 0.25 Unit A V ns C Forward voltage IAK(on) = 5 mA, Tj = -40...+150 C IAK(on) = 1.5 mA, Tj = 150 C Sensor override tP = 100 s, Tj = -40...+150 C Forward current Tj = -40...+150 C Sensor override tP = 100 s, Tj = -40...+150 C VAK(on) IAK(on) 1.3 1.4 0.9 10 5 600 V mA 5 2000-05-17 BTS 247 Z Electrical Characteristics Parameter at Tj = 25C, unless otherwise specified Sensor Characteristics Temperature sensor leakage current Tj = 150 C Min. reset pulse duration 1) Tj = -40...+150 C, IAK(on) = 0.3 mA, VAK(Reset)<0.5V VAK Recovery time1)2) Tj = -40...+150 C, IAK(on) = 0.3 mA trecovery 150 treset 100 s IAK(off) 4 A Symbol min. Values typ. max. Unit Characteristics Holding current, VAK(off) = 5V Tj = 25 C Tj = 150 C Thermal trip temperature VTS = 5V Turn-off time (Pin G+A and K+S connected) VTS = 5V, ITS(on) = 2 mA Reset voltage Tj = -40...+150C Sensor recovery behaviour: S ensor R E S E T IAK(hold) 0.05 0.05 TTS(on) toff VAK(reset) 150 0.5 0.5 160 0.5 0.3 170 2.5 - mA C s V V A K [V ] 5 4 tre s e t 0 S ensor O N R eset t re c o v e ry OFF 1See diagram Sensor recovery behaviour 2Time after reset pulse until V AK reaches 4V again 6 2000-05-17 BTS 247 Z 1 Maximum allowable power dissipation Ptot = f(TC) 130 W A 2 Drain current 40 110 100 90 30 Ptot 70 60 50 40 30 20 10 0 -40 0 40 80 120 C ID 80 25 20 15 10 5 180 0 0 20 40 TC 3 Typ. transient thermal impedance ZthJA=f(tp ) @ 6 cm2 cooling area 4 Transient thermal impedance ZthJC = f (tp ) parameter : D = tp /T 10 1 K/W Parameter: D=tp /T 10 2 K/W 10 0 D=0.5 D=0.5 0.2 Z thJC Z thJA 10 1 0.2 0.1 0.05 10 -1 0.1 0.05 0.02 10 -2 0.01 10 0 0.02 0.01 10 -3 Single pulse Single pulse 10 -1 -5 -4 -3 -2 -1 0 10 10 10 10 10 10 10 1 s 10 3 10 -4 -8 -7 -6 -5 -4 -3 -2 -1 0 10 10 10 10 10 10 10 10 10 tp 7 ID = f(TC ); VGS 4.5V 60 80 100 120 140 C 180 TC s 10 2 tp 2000-05-17 BTS 247 Z 5 Safe operating area ID=f(VDS ); D=0.01; TC =25C; VGS =4.5V 10 3 6 Typ. output characteristic ID = f(VDS); Tj =25C Parameter: VGS 120 10V A 7V 6V A Rdson=Vds/Id tp=10s 10 2 80 100s ID ID 5V 60 4.5V 1ms 10 1 10ms 100ms DC 40 4V 3.5V 20 3V 2 10 0 0 10 10 1 V 10 0 0 1 2 V 4 VDS VDS 7 On-state resistance RON = f(Tj ); ID=12A; VGS = 4.5V 60 8 On-state resistance RON = f(Tj ); ID=12A; VGS = 10V 40 max m 50 m 30 max RDS(on) 40 35 30 25 typ. RDS(on) 45 typ. 25 20 15 20 15 10 5 5 0 -50 -25 0 25 50 75 100 125 C 175 0 -50 -25 0 25 50 75 100 125 C 175 10 Tj 8 Tj 2000-05-17 BTS 247 Z 9 Typ. transfer characteristics ID = f(VGS); VDS = 12V; Tj = 25C 70 10 Typ. input threshold voltage VGS(th) = f(Tj); VDS =VGS Parameter: ID 2.4 V A 2.0 VGS(th) 50 1.8 1.6 1.4 1.2 90mA 9mA 0.9mA ID 40 30 1.0 0.8 90A 20 0.6 10 0.4 0.2 0 0 1 2 3 V 5 0.0 -50 -25 0 25 50 75 100 125 C 175 VGS Tj 11 Typ. capacitances C = f(VDS); VGS =0 V, f=1 MHz 10 1 12 Typ. forward charcteristics of reverse diode IF = f(VSD ) tp = 80s (spread); Parameter: Tj 10 2 A nF 150C 25C 10 1 C Ciss 10 0 IF 10 0 10 -1 0.0 Coss Crss 10 -1 0 4 8 12 16 20 24 28 32 V 40 0.2 0.4 0.6 0.8 1.0 V 1.4 VDS 9 VSD 2000-05-17 BTS 247 Z 13 Typ. gate charge VGS = f(QGate); ID puls = 45 A BTS 247 Z 14 Drain-source break down voltage V(BR)DSS = f(Tj ) 66 V 16 V 12 V(BR)DSS nC 100 QGate 62 VGS 10 0,2 VDS max 0,8 VDS max 60 8 58 6 56 4 54 2 52 0 0 10 20 30 40 50 60 70 80 50 -40 0 40 80 120 C 180 Tj 10 2000-05-17 BTS 247 Z Package P-TO220-5-3 9.9 9.5 3.7 Ordering Code Q67060-S6001-A2 4.4 1.3 Package P-TO220-5-62 Ordering Code Q67060-S6002-A2 4.4 9.9 8 1.3 0.2 2.4 15.6 12.8 9.2 1) 2.8 10.5 3) 9.75 5 2) 5.6 3.6 15 0.8 1.7 4x1.7=6.8 2.4 0.5 4.5 8.2 GPT05165 1.5 0.8 0.2 4 x 1.7 = 6.8 M 1.7 0.5 GPT05166 1) shear and punch direction no burrs this surface 2) min. length by tinning 3) max. 11 mm allowable by tinning 1) shear and punch direction no burrs this surface Package TO-220-5-43 Ordering Code Q67060-S6006 11 2000-05-17 1.5 9.2 1) BTS 247 Z Published by Infineon Technologies AG, Bereichs Kommunikation St.-Martin-Strasse 53, D-81541 Munchen (c) Infineon Technologies AG 1999 All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Reprensatives worldwide (see address list). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 12 2000-05-17 |
Price & Availability of BTS247Z
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |